CTP Stucco Tie

Secures delaminated stucco

  • CTP-Stucco-Tie
  • CTP-Stucco-Tie

CTP Stucco Tie

Secures delaminated stucco

The CTP Stucco Tie is a stainless steel helical shaped anchor and is used to provide a non-corrosive mechanical connection between a back-up material and stucco as a means to key the patch material mechanically to the parent structure.

Available at distributors nationwide. Call 800-255-4255.

  • Outside Tie Diameter 8mm
  • Mass: lb/ft (kg/m) 0.051 (0.076)
  • Cross Sectional Area (under load): sq in (sq mm)0.016 (10)
  • Yield Strength: ksi (N/sq mm) 108 (745)
  • Ultimate Tensile Strength: ksi (N/sq mm) 128 (880)
  • Ultimate Shear Load: ksi (pure shear, no bending) lbs (N)1169 (5200)
  • Elastic – Modulus: ksi (Gpa) 21,583.5 (148.8)
  • Helix Angle: (to longitudinal axis) 40⁰
  • Pitch Length: in. (mm) 0.79 (20)
  • Helical Pitch Length: in. (mm) 1.57 (40)
  • MaterialASTM A-167 TYPE 304 Stainless Steel

The Stucco Patch-Tie is a stainless steel helical shaped Stitch-Tie Anchor and is used to provide a non-corrosive mechanical connection between a back-up material and stucco as a means to key the patch material mechanically to the parent structure.

 

Stucco is an exterior surface treatment of buildings consisting of Portland cement plaster. Typically applied on masonry or building surfaces in thicknesses 5/8” to 1-1/2” thick. Delamination of the stucco can occur if the original construction connection has been compromised. Re-anchoring existing stucco veneer can be accomplished with 8mm x 3” or 4“ Stucco Tie helical anchors. Installed in a 3/16” pilot hole provides a threaded connection of the existing stucco and back-up masonry. The anchor is 304 SS and can be produced in 316 SS if additional corrosion protection is required. The pilot hole should be drilled at an angle, 30° – 45°, for optimum anchor engagement. However 90° to the face installations are possible in some instances.

EASY & FAST
INSTALLATION

ALMOST INVISIBLE

304 & 316
STAINLESS STEEL

REPAIR YOUR STUCCO
DON’T RE-DO IT

stucco-secures-iconSECURES SEPARATED

STUCCO

STRONG CONNECTION
TO BASE MATERIAL

CTP-Stucco-Tie-diagram
Stucco-Tie-Installation-step1

Step 1
Drill a 3/16” pilot hole using percussion hammer drill (3-jaw chuck type) through the stucco.

Stucco-Tie-Installation-step2

Step 2
Insert the CTP Stucco Tie into the dry set installation tool mounted on the rotary  hammer S.D.S. drill.

Stucco-Tie-Installation-step3

Step 3
Drive the Stucco Tie until the nose of the dry set installation tool is hard against the veneer.

Stucco-Tie-Installation-step4

Step 4
The dry set installation tool automatically recesses the Stucco Tie into the face of the stucco. Patch hole.

Kelly-Morris-PROSOCO

Kelly Morris
Product Specialist- Anchoring Systems

PROSOCO-Partnerships

News

PROSOCO acquires Construction Tie Products (CTP)

PROSOCO Inc., a Lawrence, Kan.-based manufacturer of construction chemicals, has acquired Construction Tie Products to expand its product offerings in the new construction and restoration masonry markets. Since 2005, Construction Tie Products, commonly known as CTP, has manufactured high quality masonry restoration anchors and wall ties. With staff members possessing[…]